trunk r21710 fails at launch during report loading
David Reiser
dbreiser at earthlink.net
Sun Dec 11 21:22:15 EST 2011
On Dec 11, 2011, at 3:02 PM, David Reiser wrote:
> On Dec 11, 2011, at 2:47 PM, John Ralls wrote:
>
>>
>> On Dec 11, 2011, at 11:30 AM, David Reiser wrote:
>>
>>> On Dec 11, 2011, at 1:41 PM, John Ralls wrote:
>>>
>>>>
>>>> On Dec 10, 2011, at 10:23 PM, David Reiser wrote:
>>>>
>>>>>
>>>>> On Dec 11, 2011, at 12:39 AM, John Ralls wrote:
>>>>>
>>>>>>
>>>>>> On Dec 10, 2011, at 8:03 PM, David Reiser wrote:
>>>>>>
>>>>>>> r21708 fixed my build problem (thanks John), but gnucash fails to launch with:
>>>>>>>
>>>>>>> Backtrace:
>>>>>>> In unknown file:
>>>>>>> ?: 21* [#<procedure #f ()>]
>>>>>>> ?: 22* (let* ((file #)) (cond (# => #) (# => #)))
>>>>>>> ?: 23 [#<procedure #f #> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>>>>> ?: 24 [with-fluid* #<fluid 7> #f #<procedure #f ()>]
>>>>>>> ?: 25* [#<procedure #f ()>]
>>>>>>> ?: 26* [load-file #<primitive-procedure primitive-load> ...]
>>>>>>> ?: 27* [save-module-excursion #<procedure #f ()>]
>>>>>>> ?: 28 (let (# #) (dynamic-wind # thunk #))
>>>>>>> ?: 29 [dynamic-wind #<procedure #f ()> #<procedure #f ()> #<procedure #f ()>]
>>>>>>> ?: 30* [#<procedure #f ()>]
>>>>>>> ?: 31* [primitive-load "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>>>>> In /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>>>>> 125: 32* [for-each #<procedure #f (x)> (trial-balance transaction sx-summary ...)]
>>>>>>> In unknown file:
>>>>>>> ?: 33* [#<procedure #f (x)> balsheet-eg]
>>>>>>> In /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>>>>> 127: 34* [module-use! #<directory (gnucash report standard-reports) 109f68880> ...
>>>>>>> 129: 35* [resolve-interface (gnucash report standard-reports balsheet-eg)]
>>>>>>> In unknown file:
>>>>>>> ?: 36 (letrec ((get-keyword-arg #)) (let* (# # # ...) (and # #) ...))
>>>>>>> ?: 37 (let* (# # # # ...) (and # #) (if # public-i #))
>>>>>>> ?: 38* (and (or (not module) (not public-i)) (error "no code for module" name))
>>>>>>> ?: 39 [error "no code for module" (gnucash report standard-reports balsheet-eg)]
>>>>>>> ...
>>>>>>> ?: 40 [scm-error misc-error #f ...]
>>>>>>>
>>>>>>> <unnamed port>: In procedure scm-error in expression (scm-error (quote misc-error) #f ...):
>>>>>>> <unnamed port>: no code for module (gnucash report standard-reports balsheet-eg)
>>>>>>>
>>>>>>> This looks like it might be related to moving balsheet-eg in r21591. Geert, could you take a look?
>>>>>>>
>>>>>>
>>>>>> Try:
>>>>>> make maintainer-clean
>>>>>> find src -name gnucash -type d
>>>>>> rm -rf everything you find *except* gnc-module/(foo|bar|baz)/gnucash
>>>>>>
>>>>>> Then autogen, configure, build, and install and try again.
>>>>>>
>>>>>> Regards,
>>>>>> John Ralls
>>>>>>
>>>>> I didn't exactly follow part of that: the found files were:
>>>>> src/gnc-module/test/mod-bar/gnucash
>>>>> src/gnc-module/test/mod-baz/gnucash
>>>>> src/gnc-module/test/mod-foo/gnucash
>>>>>
>>>>> Looking at the contents of one of those directories looked like it wouldn't interfere on launch. If any of those should be removed, let me know and I'll try again.
>>>>>
>>>>> But the source directory was a completely clean checkout from yesterday afternoon, and the only config/build activity was the build failure fixed in 21708.
>>>>>
>>>>> No change in result on launching gnucash. I do rm -rf base/install/dir too, before installing the new version in an old location.
>>>>
>>>> David,
>>>>
>>>> Sorry, yes, those are the directories I meant.
>>>>
>>>> What about your installation directories? Might they still have old Scheme files or shared libraries?
>>>>
>>>> Try removing (rm -rf) lib/gnucash and share/gnucash, then re-running make install.
>>>>
>>>> I just tested r21710 and it started up OK -- but I did have to clean out the installation and reinstall for it to work.
>>>>
>>>> Regards,
>>>> John Ralls
>>>>
>>> Still no joy for me. I almost always rm -rf $PREFIX/* before make install (needed once in the deep dark past, so I got in the habit of doing it every time). I also removed lib/gnucash and share/gnucash before reinstalling.
>>>
>>> My guile is not in a standard location, but that hasn't been a problem before. I'm using guile 1.8.8 and swig 2.0.4
>>
>>
>> OK, then it's not an installation problem; you must have obsolete code somewhere.
>> (Yes, I know you said it was a clean checkout.)
>>
>> $ manjusri:svn/src/gnucash-git/src> grep -r "standard-reports balsheet-eg" --include="*.scm" .
>> $ manjusri:svn/src/gnucash-git/src>
>>
>> What do you get?
>>
>> Regards,
>> John Ralls
>
> [14:57:03] dbr at DOPL6: gnucash $grep -r "standard-reports balsheet-eg" --include="*.scm" .
> [14:57:05] dbr at DOPL6: gnucash $
>
> but I think that extra balsheet-eg is coming from the (list x) in src/report/standard-reports/standard-reports.scm:
>
> (for-each
> (lambda (x)
> (module-use!
> (current-module)
> (resolve-interface (append '(gnucash report standard-reports) (list x)))))
> (get-report-list))
>
> Dave
> --
> David Reiser
> dbreiser at earthlink.net
>
I guess it's time I learned enough git to do a git bisect.
If I check out the 2.4 branch into a clean directory and build that, I get the same error. If I 'svn update -r21471' (the release point of 2.4.8, I think), make maintainer-clean, autgen/config/make/make install, that one works.
Dave
More information about the gnucash-devel
mailing list