Compiling gnucash 2.2.1 on openSuSe 10.2

[John Sved]

I installed the following from PACKMAN in this order

libktoblzcheck1-1.15-42.pm.1
ktoblzcheck-1.15-42.pm.1
libaqhbci10-2.3.2-0.pm.1
libaqbanking16-2.3.2-0.pm.1
aqbanking-qt3-2.3.2-0.pm.1
aqbanking-2.3.2-0.pm.1

then

./configure --enable-hbci

this time I noticed that the ofx hbci option was listed after it finished

make
make install

but still no setp hbci in the TOOLS menu.

regards,

John


Rauch Christian wrote:
> I have installed the following:
> 
> ktoblzcheck-1.15-42.pm.1
> libktoblzcheck1-1.15-42.pm.1
> aqbanking-2.3.2-0.pm.1
> aqbanking-qt3-2.3.2-0.pm.1
> libaqbanking16-2.3.2-0.pm.1
> libaqhbci10-2.3.2-0.pm.1
> 
> and GnuCash 2.2.1 on x86_64 from [1] and I have hbci setup in Tools.
> I don't know which aqbanking packages you installed, those from packman
> or some others?
> I did not try i586, but I suppose it works too.
> 
> Regards,
> Chris
> 
> [1]
> ftp://ftp.rauchs-home.de/suse/10.2/x86_64/gnucash-2.2.1-0.rauch.1.x86_64.rpm
> 
> John Sved schrieb:
>> Hi Chris,
>>
>> I used the openSuSE 10.2 disk via YAST to check and install where necessary:
>>
>> gtk2-devel
>> guile
>> guile-devel
>> pkgconfig
>> perl-XML-Parser
>> perl
>> libxml2-devel
>> libgnomeui-devel
>> libgnomeprint-devel
>> libgnomeprintui-devel
>> libglade2-devel
>> gtkhtml2-devel
>> doxygen
>> opensp
>> opensp-devel
>> gwenhywfar-devel
>> goffice-devel
>> libtool
>>
>> From RPM pbone.net
>>
>> libktoblzcheck-devel
>>
>> Then from RPM pbone.net  the following were downloaded.   The order is
>> as they were installed after an dependency warnings.  (i.e. this  will
>> save others going back to to fetch yet another RPM !   note make sure
>> that it is the right version for openSuSE or SuSE)
>>
>> libaqhbci10  2.3.2
>> libaqbanking16  2.3.2
>> libaqbanking-devel 2.3.2
>> libaqdtaus.so.3
>> libqbanking.so.4
>> libcbanking.so.16
>> aqbankinking-qt3 2.3.2
>> aqbanking  2.3.2
>>
>>
>> Then   ./configure --enable-hbci
>> make
>> make install
>>
>> It worked !   but   no setup HBCI in the tools menu :(
>>
>> So 3 hours of effort has not yet delivered the desired gnucash 2.2.1
>> with HBCI.
>>
>> Any suggestions ?
>>
>> regards
>> John
>>
>>
>>
>> Rauch Christian wrote:
>>   
>>> John Sved schrieb:
>>>     
>>>> Hi,
>>>>
>>>> I am really just a user of gnucash.  As I want to use the HBCI function
>>>> which is not included in the binary RPM for openSuSE 10.2   I am
>>>> reluctantly prepared to try to compile the source.  
>>>>       
>>> My Gnucash rpm is built against aqbanking, which provides HBCI.
>>> You will have to install one of aqbanking-qt3 or aqbanking-gtk2 from
>>> packman including their aqbanking to get the wizard in gnucash.
>>>
>>>     
>>>> The  aqbanking  2.2.3   from distro RPM   and  libqwenhwfar  2.6.1  from
>>>> downloaded RPM  are installed
>>>>       
>>> Use aqbanking 2.3.2 from packman (see above).
>>>
>>>     
>>>> So if someone would like to walk me through it, we may find the
>>>> necessary pieces to actually compile gnucash 2.2.1 with HBCI on
>>>> opensSuSE 10.2 for others to follow and avoid wasting a lot of time.
>>>>       
>>> Complete build requirements for Gnucash on Suse 10.2 are as follows:
>>>
>>> aqbanking libaqbanking-devel gtk2-devel guile guile-devel pkgconfig
>>> perl-XML-Parser perl libxml2-devel libgnomeui-devel libgnomeprint-devel
>>> libgnomeprintui-devel libglade2-devel gtkhtml2-devel doxygen opensp
>>> opensp-devel gwenhywfar-devel goffice-devel libtool libktoblzcheck-devel
>>>
>>> These may fetch some additional requirements I did not state explicitely.
>>>
>>>
>>>     
>>>> Thanks,
>>>>
>>>> John
>>>>       
>>> Regards,
>>> Chris
>>>
>>>
>>>     
> 
>