trunk r21710 fails at launch during report loading
David Reiser
dbreiser at earthlink.net
Sun Dec 11 14:30:20 EST 2011
On Dec 11, 2011, at 1:41 PM, John Ralls wrote:
>
> On Dec 10, 2011, at 10:23 PM, David Reiser wrote:
>
>>
>> On Dec 11, 2011, at 12:39 AM, John Ralls wrote:
>>
>>>
>>> On Dec 10, 2011, at 8:03 PM, David Reiser wrote:
>>>
>>>> r21708 fixed my build problem (thanks John), but gnucash fails to launch with:
>>>>
>>>> Backtrace:
>>>> In unknown file:
>>>> ?: 21* [#<procedure #f ()>]
>>>> ?: 22* (let* ((file #)) (cond (# => #) (# => #)))
>>>> ?: 23 [#<procedure #f #> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>> ?: 24 [with-fluid* #<fluid 7> #f #<procedure #f ()>]
>>>> ?: 25* [#<procedure #f ()>]
>>>> ?: 26* [load-file #<primitive-procedure primitive-load> ...]
>>>> ?: 27* [save-module-excursion #<procedure #f ()>]
>>>> ?: 28 (let (# #) (dynamic-wind # thunk #))
>>>> ?: 29 [dynamic-wind #<procedure #f ()> #<procedure #f ()> #<procedure #f ()>]
>>>> ?: 30* [#<procedure #f ()>]
>>>> ?: 31* [primitive-load "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>> In /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>> 125: 32* [for-each #<procedure #f (x)> (trial-balance transaction sx-summary ...)]
>>>> In unknown file:
>>>> ?: 33* [#<procedure #f (x)> balsheet-eg]
>>>> In /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>> 127: 34* [module-use! #<directory (gnucash report standard-reports) 109f68880> ...
>>>> 129: 35* [resolve-interface (gnucash report standard-reports balsheet-eg)]
>>>> In unknown file:
>>>> ?: 36 (letrec ((get-keyword-arg #)) (let* (# # # ...) (and # #) ...))
>>>> ?: 37 (let* (# # # # ...) (and # #) (if # public-i #))
>>>> ?: 38* (and (or (not module) (not public-i)) (error "no code for module" name))
>>>> ?: 39 [error "no code for module" (gnucash report standard-reports balsheet-eg)]
>>>> ...
>>>> ?: 40 [scm-error misc-error #f ...]
>>>>
>>>> <unnamed port>: In procedure scm-error in expression (scm-error (quote misc-error) #f ...):
>>>> <unnamed port>: no code for module (gnucash report standard-reports balsheet-eg)
>>>>
>>>> This looks like it might be related to moving balsheet-eg in r21591. Geert, could you take a look?
>>>>
>>>
>>> Try:
>>> make maintainer-clean
>>> find src -name gnucash -type d
>>> rm -rf everything you find *except* gnc-module/(foo|bar|baz)/gnucash
>>>
>>> Then autogen, configure, build, and install and try again.
>>>
>>> Regards,
>>> John Ralls
>>>
>> I didn't exactly follow part of that: the found files were:
>> src/gnc-module/test/mod-bar/gnucash
>> src/gnc-module/test/mod-baz/gnucash
>> src/gnc-module/test/mod-foo/gnucash
>>
>> Looking at the contents of one of those directories looked like it wouldn't interfere on launch. If any of those should be removed, let me know and I'll try again.
>>
>> But the source directory was a completely clean checkout from yesterday afternoon, and the only config/build activity was the build failure fixed in 21708.
>>
>> No change in result on launching gnucash. I do rm -rf base/install/dir too, before installing the new version in an old location.
>
> David,
>
> Sorry, yes, those are the directories I meant.
>
> What about your installation directories? Might they still have old Scheme files or shared libraries?
>
> Try removing (rm -rf) lib/gnucash and share/gnucash, then re-running make install.
>
> I just tested r21710 and it started up OK -- but I did have to clean out the installation and reinstall for it to work.
>
> Regards,
> John Ralls
>
Still no joy for me. I almost always rm -rf $PREFIX/* before make install (needed once in the deep dark past, so I got in the habit of doing it every time). I also removed lib/gnucash and share/gnucash before reinstalling.
My guile is not in a standard location, but that hasn't been a problem before. I'm using guile 1.8.8 and swig 2.0.4
Dave
--
David Reiser
dbreiser at earthlink.net
More information about the gnucash-devel
mailing list