trunk r21710 fails at launch during report loading

[John Ralls]

On Dec 11, 2011, at 11:30 AM, David Reiser wrote:

> On Dec 11, 2011, at 1:41 PM, John Ralls wrote:
> 
>> 
>> On Dec 10, 2011, at 10:23 PM, David Reiser wrote:
>> 
>>> 
>>> On Dec 11, 2011, at 12:39 AM, John Ralls wrote:
>>> 
>>>> 
>>>> On Dec 10, 2011, at 8:03 PM, David Reiser wrote:
>>>> 
>>>>> r21708 fixed my build problem (thanks John), but gnucash fails to launch with:
>>>>> 
>>>>> Backtrace:
>>>>> In unknown file:
>>>>> ?: 21* [#<procedure #f ()>]
>>>>> ?: 22* (let* ((file #)) (cond (# => #) (# => #)))
>>>>> ?: 23  [#<procedure #f #> "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>>> ?: 24  [with-fluid* #<fluid 7> #f #<procedure #f ()>]
>>>>> ?: 25* [#<procedure #f ()>]
>>>>> ?: 26* [load-file #<primitive-procedure primitive-load> ...]
>>>>> ?: 27* [save-module-excursion #<procedure #f ()>]
>>>>> ?: 28  (let (# #) (dynamic-wind # thunk #))
>>>>> ?: 29  [dynamic-wind #<procedure #f ()> #<procedure #f ()> #<procedure #f ()>]
>>>>> ?: 30* [#<procedure #f ()>]
>>>>> ?: 31* [primitive-load "/opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm"]
>>>>> In /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>>> 125: 32* [for-each #<procedure #f (x)> (trial-balance transaction sx-summary ...)]
>>>>> In unknown file:
>>>>> ?: 33* [#<procedure #f (x)> balsheet-eg]
>>>>> In /opt/gnucash-svn/share/gnucash/guile-modules/gnucash/report/standard-reports.scm:
>>>>> 127: 34* [module-use! #<directory (gnucash report standard-reports) 109f68880> ...
>>>>> 129: 35* [resolve-interface (gnucash report standard-reports balsheet-eg)]
>>>>> In unknown file:
>>>>> ?: 36  (letrec ((get-keyword-arg #)) (let* (# # # ...) (and # #) ...))
>>>>> ?: 37  (let* (# # # # ...) (and # #) (if # public-i #))
>>>>> ?: 38* (and (or (not module) (not public-i)) (error "no code for module" name))
>>>>> ?: 39  [error "no code for module" (gnucash report standard-reports balsheet-eg)]
>>>>> ...
>>>>> ?: 40  [scm-error misc-error #f ...]
>>>>> 
>>>>> <unnamed port>: In procedure scm-error in expression (scm-error (quote misc-error) #f ...):
>>>>> <unnamed port>: no code for module (gnucash report standard-reports balsheet-eg)
>>>>> 
>>>>> This looks like it might be related to moving balsheet-eg in r21591. Geert, could you take a look?
>>>>> 
>>>> 
>>>> Try: 
>>>> make maintainer-clean
>>>> find src -name gnucash -type d
>>>> rm -rf everything you find *except* gnc-module/(foo|bar|baz)/gnucash
>>>> 
>>>> Then autogen, configure, build, and install and try again.
>>>> 
>>>> Regards,
>>>> John Ralls
>>>> 
>>> I didn't exactly follow part of that: the found files were:
>>> src/gnc-module/test/mod-bar/gnucash
>>> src/gnc-module/test/mod-baz/gnucash
>>> src/gnc-module/test/mod-foo/gnucash
>>> 
>>> Looking at the contents of one of those directories looked like it wouldn't interfere on launch. If any of those should be removed, let me know and I'll try again.
>>> 
>>> But the source directory was a completely clean checkout from yesterday afternoon, and the only config/build activity was the build failure fixed in 21708.
>>> 
>>> No change in result on launching gnucash. I do rm -rf  base/install/dir too, before installing the new version in an old location.
>> 
>> David,
>> 
>> Sorry, yes, those are the directories I meant.
>> 
>> What about your installation directories? Might they still have old Scheme files or shared libraries?
>> 
>> Try removing (rm -rf) lib/gnucash and share/gnucash, then re-running make install.
>> 
>> I just tested r21710 and it started up OK -- but I did have to clean out the installation and reinstall for it to work.
>> 
>> Regards,
>> John Ralls
>> 
> Still no joy for me. I almost always rm -rf $PREFIX/* before make install (needed once in the deep dark past, so I got in the habit of doing it every time). I also removed lib/gnucash and share/gnucash before reinstalling. 
> 
> My guile is not in a standard location, but that hasn't been a problem before. I'm using guile 1.8.8 and swig 2.0.4


OK, then it's not an installation problem; you must have obsolete code somewhere.
(Yes, I know you said it was a clean checkout.)

$ manjusri:svn/src/gnucash-git/src> grep -r "standard-reports balsheet-eg" --include="*.scm" .
$ manjusri:svn/src/gnucash-git/src> 

What do you get?

Regards,
John Ralls